Neu

XRAY ALU SHIM 3x6x3.0MM - ORANGE (10) - 303125-O

XRAY REAR ADJUSTABLE DRIVE AXLE LB - HUDYSPRING STEEL - 325341

XRAY ALU SHIM 10x12x2MM (2) - 325390

XRAY BODY FOR 1/10 2WD OFF-ROAD BUGGY 0.75MM - BETA 2 - 329707

XRAY COMPOSITE STEERING BLOCK - HARD - 362250-H

XRAY GEAR DIFFERENTIAL FOR 2.5MM PIN - SET - 364902

XRAY GEAR DIFF OUTDRIVE ADAPTER FOR 2.5MM PIN - HUDYSPRING STEEL (2) - 364961

XRAY STEEL BEVEL DRIVE GEAR - CNC-MACHINED - 14T - 365124

XRAY FRONT DRIVE SHAFT 81MM WITH 2.5MM PIN - HUDYSPRING STEEL - 365222

XRAY CENTRAL SHAFT UNIVERSAL JOINT FOR MACHINED PINION - 365442

FRONT linear springs have been specifically designed to complement the big-bore shocks. Spring rate is constant during the entire spring compression. Marked with 2 DOTS for easy identification.

The springs, like all the other XRAY springs, are manually measured, selected and matched into pairs to guarantee precisely equal length and damping characteristics. 

Motiv Universal Bearing Tool (All Brand Motors) - MOV1960

What makes this bearing tool special is its ability to adapt to any design motor and also that it can be completely rebuilt to replace any part necessary in the event that something strips or gets bent. Included are three different cup sizes which will allow you to choose the proper place on your sensor unit or end bell to apply the pressure necessary to install new bearings. This results in drastically reducing the chance of motor damage during bearing installation.

 

Mon-Tech 0.75mm Racer Wing Medium - 018-003M

Mon-tech F18 Formula Body shell - 018-009

MR33 V4 Carpet Additive 100ml ETS - MR33-0004

SANWA MX-6 Radio Set with RX-391W - 101A32571A

Speedtech RC Foam Liquid multiple world champion and european champion - MOB1000

MobGums 1/12 dishers rear tyres white compound for ETS carpet - MOBR335

MobGums 1/12 dishers rear tyres silver compound for ETS carpet - MOBR135

MobGums 1/12 dishers front tyres white compound for ETS carpet - MOBF035

MobGums 1/12 dishers front tyres silver compound for ETS carpet new! - MOBF135

Schumacher Cut Stagger - 2WD Low Profile Front Tyres - Yellow (1 pair) - U6770

XRAY Graphite Rear Gear Diff Axle Shaft - 375014

XRAY COMPOSITE BALL-BEARING HUB (2) - 372072

Alu Upper Eccentric Clamp for Ball-Bearing

• Rear wheelbase adjustment

• Ultra-light

• Ultra-strong

• Black coated

Ultra-light, ultra-strong eccentric upper clamp for ball-bearing (without use of composite hub), CNC-machined from premium Swiss 7075 T6 aluminum. Eccentric upper clamps allow movement of the rear axle 1mm forward or rearward depending on the clamp orientation.

A shorter car rotates faster in slow corners and has improved forward traction. A longer car is freer in high-speed corners and will feel more linear, especially during fast direction changes.

Additionally black coated for long life and stylish look. Identical left/right. Fits alu rear bulkheads with quick & easy ride height adjustment.

Fits X12 and X1.

XRAY X12'19 GRAPHITE BATTERY BACKSTOP 2.0MM - 373087

XRAY X12'19 REAR BRACE - GRAPHITE 2.5MM - 373086

XRAY X12'19 GRAPHITE BUMPER LOWER HOLDER 2.5MM - 371211

XRAY X12'19 ALU CHASSIS 2.0MM - 7075 T6 - 371112

XRAY X12'19 GRAPHITE CHASSIS 2.5MM - 371111

XRAY X12'19 ALU REAR BULKHEAD - MOTOR (LEFT) - 373026

Hobbywing Combo XR10 PRO & V10 G3 - C: 5.5T 5900kv - 38020230

Product information "Hobbywing Xerun XR10 Pro Brushless ESC Black 160A, 2-3s LiPo"

All the products in this series are sensored brushless power systems for professional races range from 1/12th scale to 1/8th scale, from Modified to Stock. Their excellent performance, reliable structure design and others definitely can meet top-level races strict requirements against products performance and quality.
The XR10 Pro is a real and maybe THE ESC for 1/10 competition use. Doesn`t matter if On-Road touring cars or Off-Road Buggies, the feeling and power with this ESC is amazing. With outstanding features like Data-logging Function, adjustable Throttle and Brake frequencies, powerful BEC and a max. const. current of 160A.

High Power Output
Continuous current of 160A and peak current of up to 1200A guarantees a stable and high power output during competitions.

Special Design for Top Racing
Reliable hardware combined with intelligent software (containing 10 common select-to-use profiles) creates an ideal power solution to 1/10th scale top touring car, Pan car and buggy racing.

Programming / Upgrading / Data reading wirelessly
With Hobbywings WiFi Express module and iPhone or an Android phone (with the HOBBYWING WiFi Link software installed), the user can remotely program parameters, upgrade firmware and check relevant data of the ESC without leaving the control stand.

Adjustable Throttle & Brake PWM Frequencies
Independent and adjustable throttle & brake PWM frequencies guarantee precise and accurate throttle and brake control for all classes of competitions (esp. the Stock class).

Efficient Heat Dissipating System
The aluminum casing and reticular heat sink combined with the HOBBYWING patented copper heat-conductive plates which are attached to the MOSFET board allows the internal heat to be quickly transferred to the heat sink for dissipation. With the high-performing detachable cooling fan, a highly reliable heat transfer system for maximum cooling is accomplished.

High current/voltage BEC
The built-in switch mode BEC with a maximum output of 4A and voltage adjustable between 6V and 7.4V allows the user to use various high voltage servos.

Separate Programming/Fan Port
The separate PRG/FAN port on the ESC can power an external fan for maximize cooling performance or connect the ESC to a LCD program box or WiFi module for ESC programming.

Advanced and Secure Electronic Switch
The XR10 Pro ESC features an electronic switch with a lifespan of over 50000 on/off cycles, housed in a completely waterproof, dust-proof and shock-resistant design.

Innovative data-logging Function
This ESC features the data-logging function which can record the maximum ESC/motor temperature, RPM and etc. in real time and allows the user to analyze the recorded data via a the LCD program box or WiFi module after each use.


Specifications

• Type
  • Scale: 1/10th
  • Brushed/Brushless: BL
  • Sensored/Sensorless: SD
  • Waterproof: No
• Specifications
  • Cont./Peak Current: 160A/1200A
  • Input: 2-3S LiPo / 4-9 Cell NiMH
  • BEC Output: Swich Mode: 6V / 7.4V max. 4A
• Wires & Connectors
  • Input Wires: Black-12AWG-200mm*2
  • Output Wires: Black-12AWG-200mm*3
  • Input Connectors: No
  • Output Connecotors: No
• Fan
  • Size: 25.0x25.0x10.0mm
  • Voltage Range: 5-7.4V
  • Powered by: Powered by BEC
• ESC Programing via
  • LCD Program Box: Supported
  • WiFi Module: Supported
  • Program Port: Separate Program Port
• Size & Weight
  • Size: 37.5x30.9x31.6mm(w/Fan & Fan Shroud)
  • Weight: 95g(w/ Wires)
• Applications
  • Motors: SL BL Motors / SD BL Motors
  • Vehicles: 1/10th Touring Car & Buggy & Drift Car & F1; 1/8th,1/10th Rock Crawler
  • KV Rating/T Count:
    • 2S LiPo/6S NiMH: (Touring Car) T=3.5T, (Buggy) T=4.5T.
    • 3S LiPo/9S NiMH: (Touring Car) T=6.5T, (Buggy) T=8.5T.

Product Comparison

Hobbywing Combo XR10 PRO & V10 G3 - B: 4.5T 7340kv - 38020229

PowerHD Black Colour R12 Servo - PHD-R12

Perfecte servo voor 1/10 Toerwagen 1/10 Buggy M-Chassis of F1 met een prima prijs!

Kenmerken:
Koppel (6,0 V): 9,0 kg-cm (125,0 oz / in) Koppel (7,4 V): 12,0 kg-cm (166,6 oz / in)
Snelheid: 0,07 sec (6,0 V) | 0,06 sec (7,4 V)
Bedrijfsspanning: 6,0 ~ 8,4 DC Volts Gewicht: 41,0 g (1,45 oz)
Type lager: kogellager x 2
Motortype: kernloze motor
Versnellingstype: Titan en aluminium
Bedrijfstemperatuur: -20? ~ 60?
Werkfrequentie: 1520μs / 333hz
Grootte: 41.0 x 20.0 x 26.4 mm (1.61 x 0.79 x 1.04 in)
Servohorn: 25 tands (niet inbegrepen)

RacingLine-RC Tire Cutter Pro - RL-0001

Racingline-RC Tyre-Cutter Haal het maximale uit je nieuwe set banden.

Alu Servo Horn 1/8 Off-Road Futaba - 25T - 293503

ALU SERVO HORN - FUTABA - 2-HOLE - 25T - 293499

ALU SERVO HORN - FUTABA - OFFSET - 25T - 293493