Corner Speed RC MAXI free CV Joint lube - CS800102

Maxi Free CV Joint Lube is a deep penetrating teflon lubricant that works flawlessly in all conditions both on and off road. Unlike other wet lubricants, Maxi Free goes on wet and setup with a supper dry, hard and extremely durable thin film that wicks away dirt, carpet hair or tyre rubber during the races. Maxi Free is the answer for racers who looking for a super clean, long lasting and low friction CV joints and universals.

Shake well before use. Apply on clean joints to maximise the performance of the lube.

-Long lasting
-Super dry lube
-Doesn’t attract dirt
-Extra smooth operation
-Feature a needle tip bottle, easier to apply on small parts

XRAY PURE TUNGSTEN CHASSIS WEIGHT 13g (2) - 306550

Machined 13g pure tungsten chassis weight. The weights are smaller than the brass weights and are easier to install with a cleaner layout. The super small weights result in lower CG comparing to standard weights. 

Produced from very rare and heavy pure tungsten material, not a typical tungsten mixture. The pure tungsten has the highest density structure and is the heaviest metal material which allows to design smallest size weights comparing to any other materials.

Quick & easy attachment to chassis. Marked with weight value for easy identification. 
 

XRAY PURE TUNGSTEN CENTER CHASSIS WEIGHT 30g - 309856

Machined 30g pure tungsten chassis weight. The weights are smaller than the brass weights and are easier to install with a cleaner layout. The super small weights result in lower CG comparing to standard weights. 

Produced from very rare and heavy pure tungsten material, not a typical tungsten mixture. The pure tungsten has the highest density structure and is the heaviest metal material which allows to design smallest size weights comparing to any other materials.

Quick & easy attachment to chassis. Marked with weight value for easy identification.
 

LRP X22 Stock Spec - 10.5T - 520200

LRP X22 Stock Spec - 10.5T - 520200

LRP X22 Stock Spec - 13.5T - 520201

LRP X22 Stock Spec - 13.5T - 520201

LRP X22 Stock Spec - 17.5T - 520202

LRP X22 Stock Spec - 17.5T - 520202

LRP X22 Stock Spec - 21.5T - 520203

LRP X22 Stock Spec - 21.5T - 520203

Hiro Seiko M3x8 Titanium Hex Socket Flat Head Screw - 69688

Hiro Seiko M3x8 Titanium Hex Socket Flat Head Screw (5)

MonkeyKingRC Charge Lead XH2S Balance Port-B - MK2976BK

2S Lipo charge lead with 4mm charger input plugs and 4-5mm battery plugs, including 2mm balance plug. 600mm. Extremely versatile, suits a wide range of chargers!

Mon-Tech M-Truck 2.0 - 019-003

The body utilises only three parts - the base, cabin and rear wing, making it both lightweight and durable and it incorporates details such as a mock-up engine and the ability to fine-tune the wing setting for low and high downforce. The shape ensures it can be mounted on all kinds of touring car chassis without having to cut the front bumper and it is made of high-quality 0.75mm polycarbonate. Included with the body set come window masks, a decal sheet and the needed assembly hardware.

XRAY LEXAN REAR WING - LOW TRACTION - 323513

XRAY LEXAN REAR WING - LOW TRACTION - 323513

XRAY LEXAN FRONT WING - DIV - 323516

Stylish, effective wider front wing works perfectly with XRAY XB2 body and increases front down force. Multiple mounting positions allow to change the position of the wing and alter the down force. Made from strong high quality Lexan material.

XRAY LEXAN REAR WING - TEC - 323517

Stylish, effective rear wing works perfectly with XRAY XB2 body. Flat design helps to get more rotation coming into the corner and increases traction coming out of corner. Made from strong high quality Lexan material.
 

XRAY GEAR DIFFERENTIAL 1/10 PAN CAR - SET - 374902

 

XRAY self-designed, revolutionary, super-smooth gear diff for 1/10 pan cars is a direct replacement for the ball-differential; it is a complete set which requires no other extra parts and no extra adjustments. Using the gear differential makes the car more stable and easier to drive, especially in high-traction conditions. The gear diff increases on-power steering which is needed on almost all types of tracks. A “must have” for every racer. The complete gear differential set includes a composite case and cover, precision-molded internal satellite gears made from special XRAY-developed composite material, all ensuring long lifespan and super-smooth efficient operation. A super-strong hollow steel shaft ensures maximum reliability and strength. The advantage of the gear diff is that it is maintenance-free. When the diff is correctly built, there is no need for maintenance for a very long time, no need for frequent oil changes, and no leakage due to a superior sealing system.

 

HUDY ALU TRAY FOR ON-ROAD DIFF & SHOCKS - 109800

Professional, ultra-compact work tray for diff & shocks rebuild. CNC-machined from one-piece aircraft aluminum. Extremely durable and wear resistant thanks to the hard black coating. The parts tray features 4 compartments for each of the shocks laser edged with label. Perfect for 1/10, 1/12 & 1/8 on-road cars. Includes easily removable aluminum shock stand. Shock stand sets are available separately to convert between vehicle types. Machined pockets feature super thin walls for weight saving. Stylish chamfered edges and laser engraved HUDY graphics makes your tray stand out on your pit table.

HUDY ALU TRAY FOR SET-UP SYSTEM - 109860

HUDY Alu Tray for Set-Up System
 

• Ultra-compact work tray for set-up system & tools

• Features various compartments for set-up system parts, shock stands, set-up wheels, balancing tools, and other accessories

• Rear part of the tray features slot for set-up system upside measurement plate

• CNC-machined from 1-piece aircraft aluminum for durability

• Machined pockets with super-thin walls for weight saving

• Stylish chamfered edges

• Super-hard coated for wear resistance protection

• Perfect for all classes & scales
 

Professional, ultra-compact work tray for set-up system and tools. CNC-machined from 1-piece aircraft aluminum. Extremely durable and wear resistant due to hard black coating.

The parts tray features various compartments for set-up system parts, shock stands, set-up wheels, balancing tools, and other accessories. Perfect for all classes and scales. Rear part of the tray features slot for set-up system upside measurement plate.

Machined pockets feature super-thin walls for light weight. Stylish chamfered edges and laser-engraved HUDY graphics makes your tray stand out on your pit table.

#109860 HUDY Alu Tray for Set-Up System

HUDY ALU TRAY FOR ACCESSORIES & PIT LED - 109880

HUDY Alu Tray for Accessories & Pit LED


•          Ultra-compact work tray for accessories, Pit LED, and mobile phone
•          Features 4 different compartments for accessories & hardware
•          Middle compartment fits perfectly to #107855 - HUDY Pit LED
•          Front adjustable bar holds your mobile phone
•          CNC-machined from 1-piece aircraft aluminum for durability
•          Machined pockets with super-thin walls for light weight
•          Stylish chamfered edges
•          Black coated
•          Perfect for all classes & scale
•          Part of the HUDY Tray System


Professional, ultra-compact work tray for accessories, Pit LED, and mobile phone. CNC-machined from 1-piece aircraft aluminum. Extremely durable and wear resistant. Black coated.

The parts tray features 4 different compartments for accessories & hardware. Middle compartment fits perfectly to #107855 - HUDY Pit LED. Front adjustable bar holds your mobile phone.

Machined pockets feature super-thin walls for light weight. Stylish chamfered edges and laser-engraved HUDY graphics makes your tray stand out on your pit table.

HUDY PROFESSIONAL BULKHEAD ALIGNMENT TOOL 19MM - 183000

#183000 HUDY Professional Bulkhead Alignment Tool 19mm

• Perfect bulkhead alignment
• For 19mm bulkhead spacing
• Comfortable & fast
• Lightweight 
HUDY Bulkhead Alignment Tool for touring car bulkheads with spacing of 19mm allows for easy, comfortable and fast alignment of bulkheads. 

The alignment tool is placed between the left and right bulkheads with the included steel shafts. With the block and pins in place the driver can loosen and retighten both the lower bulkhead mounting screws and also the upper clamps and shock towers for perfect alignment of all parts. After all the parts are straightened up, the pins and block will be removed, the diff or spool installed and the bulkhead upper clamps installed. 

CNC-machined from lightweight aircraft aluminum and laser edged for autentic look this is a must have tool for all touring car drivers. The alignment tool works perfectly for all XRAY T4 platforms and other touring cars with 19mm spacing between bulkheads.

XRAY GRAPHITE GEAR BOX HEIGHT ADJUSTMENT PLATE - 321269

CNC-machined gear box height adjustment plate made from premium-grade graphite material. Allows super-low ride height in high-traction conditions for improved performance. To keep the drive shafts linear, these optional graphite plates raise the gear box by 2mm. There are two different ride height adjustable plates which raise either only the gear box, or the entire rear suspension.

Must be used with #324013 Alu Front-Mid Motor (3 Gears) Plate - Lowered -2mm - 7075 T6.
 

Hobbywing XERUN V10 G3 Rotor 12.5T - 30820401

HOBBYWING  is proud to present the newest rotor(5-12.3/12.5-U-T) for the V10 G3 motor series.

The characteristic of the titanium bonded rotor provides a milder, smoother pickup acceleration without losing its top speed. The rotor will aid drivers especially on lower grip surfaces and allow drivers to accelerate quicker out of tighter corners. The rotor has been extensively tested and race proven by Top Drivers on carpet and  low grip asphalt tracks around the world. Highly recommended for all HOBBYWING XR10 Pro users on their Modified motors.

Hobbywing XERUN V10 G3 Rotor 12.3T - 30820402

HOBBYWING  is proud to present the newest rotor(5-12.3/12.5-U-T) for the V10 G3 motor series.

The characteristic of the titanium bonded rotor provides a milder, smoother pickup acceleration without losing its top speed. The rotor will aid drivers especially on lower grip surfaces and allow drivers to accelerate quicker out of tighter corners. The rotor has been extensively tested and race proven by Top Drivers on carpet and  low grip asphalt tracks around the world. Highly recommended for all HOBBYWING XR10 Pro users on their Modified motors.

BittyDesign JP8 1/10 TC 190mm body (Light) - BDTC-190JP8

When thinking about the best think about the JP8.

The ALL NEW ultra downforce body shell has been developed with the collaboration of our wordwide team drivers, who participated to the several stages of the project. The JP8 includes all of our experience gained in over 10 years of presence on the racetrack, and the final version of the body requested many changes before reach the perfect shape. To raise the bar we not accepted any compromise.

Tested for several months both indoor and even outdoor on different types of carpet and tarmac, the JP8 body shell represent a new reality for drivers all around the world who race at top levels and always want to obtain the best result with their models.

 

No Compromise

The JP8 project is born with one main target: create an all new ultra downforce body shell that can be the fastest, always. No matter what final shape and lines the body will have, how it will look, the focus during the designing stage has been pure performance.

LIGHTNESS and STRENGTH! Thanks to an excellent production process, which guarantees a high homogeneity of the material in any area of the body, we have reached a good compromise between weight and durability of the product. Several track tests have revealed excellent impact resistance, giving the JP8's extremely longevity.


 

The Art of Performance at his best

To achieve the best result possible in term of overall product we have made the most of all our know-how, our experience on the track allowed to us to develop, to design, to engineer and to test for several months a body shell that represent the new future for the 1/10 TC competitions.

The ultra downforce design generate impressive steering as well an excellent rear stability; very easy to push the car at limit, the driving feeling is great both on indoor and outdoors layouts.

---

Product Features

The body respect all the international specs necessary for the approval by the federations, its EFRA, IFMAR and BRCA homologated.

• Made with high quality and genuine polycarbonate Lexan®
• Included in the kit a complete set of screw, nuts and large plastic washers to fix properly the rear wing
• Produced in Light Weight version, thickness of material 0,75mm
• Sold clear with protective film outside
• Included in the package a few decal sheets pre-cut and windows mask

---

Track Guide for the use of the JP8 body

The following values offer an overview of the ideal conditions of use of the body according to the grip of the surface and its general handling.

The numbers below are meant as a progressive scale where 10 is a hypothetical maximum value.

   
Surface grip 
7 
Enter Steering
10
Rear stability
10
Ease of use
10

 

XRAY ORANGE Offset Spur Gear 100T : 64 - 305870-O

XRAY ORANGE Offset Spur Gear 100T : 64 - 305870-O

XRAY COMPOSITE SERVO SAVER - GRAPHITE - 362510-G

 

• Special graphite composite mixture • Increased strength • Improved friction • Lower weight • Reliable • Durable

   

Molded composite servo saver parts made from specially-formulated graphite composite mixture for increased strength, improved friction and lower weight. Perfect balance between reliability and performance.

XRAY XB4 Composite Steering Plate - Graphite - 362571-G

XB4 Composite Steering Plate - Graphite
 

• Special graphite composite mixture

• Increased strength

• Increases steering precision

• Lower weight

• Reliable

• Durable

Molded composite steering plate made from specially-formulated graphite composite mixture for increased strength and lower weight. Increases steering precision. Perfect balance between reliability and performance.

CS High Grip Carpet Additive 100ml - C6400

CS High Grip Carpet Additive 100ml - C6400
GEBRUIK VOOR INDOOR RUBBER/FOAM BANDEN

XRAY Composite Suspension Arm Rear Lower Left - Graphite - 363122-G

XB4 Composite Suspension Arms Rear Lower - Graphite

• Special graphite composite mixture

• Increases stability

• Increases cornering speed

• Lightweight

• For High traction tracks

• Durable

Rear lower suspension arms made from specially-formulated graphite composite mixture, perfect for high-traction conditions. The graphite arms make the car more stable and give increased cornering speed. Intelligent arm design allows for variable positioning of the rear shocks. Depending on track conditions, the rear shocks can be installed either in front of or behind the rear shock tower, and the rear shock tower can be placed either in front of or behind the bulkhead.

XRAY Composite Suspension Arm Rear Lower Right - Graphite - 363112-G

XB4 Composite Suspension Arms Rear Lower - Graphite

• Special graphite composite mixture

• Increases stability

• Increases cornering speed

• Lightweight

• For High traction tracks

• Durable

Rear lower suspension arms made from specially-formulated graphite composite mixture, perfect for high-traction conditions. The graphite arms make the car more stable and give increased cornering speed. Intelligent arm design allows for variable positioning of the rear shocks. Depending on track conditions, the rear shocks can be installed either in front of or behind the rear shock tower, and the rear shock tower can be placed either in front of or behind the bulkhead.

XRAY ALU STEERING PLATE REARWARD LINKAGE MOUNTING - SWISS 7075 T6 - 322572

• More linear steering
• More predictable handling
• More precise steering
• Easily adjustable Ackermann positions

Alu steering plate for rearward linkage mounting allows mounting the steering linkages more rearwards which makes the steering more linear and makes the car more predictable. Ackermann is easily adjusted via steering link mounting positions on the steering plate. The alu steering plate gives more precise steering, but makes the steering more aggressive. CNC-machined from premium Swiss 7075 T6 aluminum

HUDY AIR VAC - VACUUMPUMP - ON-ROAD 1/8, 1/10, 1/12 - 104002

 

HUDY Air Vac is a handy, ultra-compact electric-powered vacuum pump for on-road shock absorbers, developed to quickly & easily bleed unwanted air bubbles from oil-filled shock absorbers and differentials. Electrically operated, simple operation. 

The main platform is fully CNC-machined from aluminum, and includes exchangeable shock/diff stands and transparent plastic cover. 

Air Vac includes strong & effective vacuum pump that is powered by 12V power supply or 7.2V battery (not included). Includes holders for shock absorbers and differential, 600mm connecting cable with gold-plated banana plugs. Comes in a premium hard case for safe storage & transport. 

This high-quality premium device is fully produced and assembled by HUDY in Europe.

Available in 3 different sizes for on-road, 1/10 off-road, and 1/8 off-road. 
 

HUDY 1/10 TC Tires A1-36 - Asphalt (4) - 803062

HUDY 1/10 TC Tires A1-36 - Asphalt
 

* 1/10 touring car tires

* A1-36 compound for asphalt tracks

* Improved traction & durability

* Unique tough rubber compound

* Improved lifetime

* Factory pre-glued

* Optimized new insert hardness

* Optimized new insert thickness

* Reinforced and stronger wheels

* Set of 4

 

The A1-36 is a tire specifically designed for asphalt tracks, and it has a unique tough rubber compound formulated for high-competition asphalt racing. New improved compound improves traction but at the same time makes the car more stable and easier to drive. The lifetime and reliability of the rubber is significantly improved as well.

Set of 4 tires includes new inserts with improved quality and optimized hardness and thickness. Tires are precision pre-glued on HUDY touring car wheels moulded from our own composite mixture to ensure true fit, vibration-free running as well as proper hardness matched to the tire compound. The new wheel material improves durability.

An overall no-compromise, high-competition racing tire with maximum traction and unmatched stability.

Hobbywing XeRun XR10 PRO-STOCK SPEC V4 ESC 80A Black - 30112401

Hobbywing XeRun XR10 PRO-STOCK SPEC V4 ESC 80A Black - 30112401

PROTOFORM Europa Clear Body for 190mm FWD Class - 1565-25

 

PROTOform is excited to bring our first-ever body dedicated to front wheel drive touring cars: meet the Europa.

Europa takes styling cues from popular European hot hatches competing in full-scale TCR classes around the globe. With aggressive fender flares and a slammed hatchback roofline, the Europa is bound to make a statement at your track. At the rear of the body, molded in wing platforms support the add-on nylon wing struts and wing to complete the super scale look. Designed and produced using the latest in 3D CAD and 5-axis CNC technology, Europa’s detailing, symmetry and overall quality of surfaces is second-to-none.

This body will fit any popular 190mm touring car chassis. It’s produced in our high-quality, lightweight polycarbonate for a low center of gravity, and includes a detailed decal sheet with windshield header and number plates, window masks, and paint-then-peel overspray film.
 

SKYRC DC Power Distributor (Banana connector) - 600114-01

SKYRC DC Power Distributor (Banana connector)

XRAY BRASS REAR CHASSIS BRACE WEIGHT 40G - 361179

Optional brass chassis brace fits in the lower part of the composite brace connected directly to the chassis, generating more stability. When using this brace, the composite rear lower brace must be removed. The weight of the car is moved more to the rear, improving the rotation of the car and lowering CG.

XRAY X1'19 GRAPHITE CHASSIS 2.5MM - HARD - 371019

Chassis design, layout, and flex have significant influence on the handling of the X1. The 2.5mm chassis made from harder graphite material was developed for very-high traction conditions, or when using tires that offer a lot of steering which makes the car more difficult to drive. This chassis makes the car more stable and easier to drive, and eliminates oversteering.

The super-narrow chassis front allows for maximum traction while having excellent steering and cornering speed. The chassis has ideal torsional stability to help eliminate the “scrub effect” in high-speed corners.

 

XRAY X1'19 GRAPHITE ARM MOUNT PLATE - WIDE TRACK-WIDTH - 2.5MM - 371065

XRAY X1'19 GRAPHITE ARM MOUNT PLATE - WIDE TRACK-WIDTH - 2.5MM - 371065

XRAY X1'19 GRAPHITE REAR BRACE 2.5MM - 371078

XRAY X1'19 GRAPHITE REAR BRACE 2.5MM - 371078

XRAY X1'19 GRAPHITE PLATE FOR MOUNTS 2.5MM - 371096

XRAY X1'19 GRAPHITE PLATE FOR MOUNTS 2.5MM - 371096

XRAY X1'19 GRAPHITE LOWER SUSPENSION ARM 2.5MM - 372117

XRAY X1'19 GRAPHITE LOWER SUSPENSION ARM 2.5MM - 372117

XRAY X1'19 ALU REAR BULKHEAD - MOTOR (RIGHT) - 373015

XRAY X1'19 ALU REAR BULKHEAD - MOTOR (RIGHT) - 373015

XRAY X1'19 ALU REAR BULKHEAD - LEFT - 373025

XRAY X1'19 ALU REAR BULKHEAD - LEFT - 373025

XRAY X1'19 GRAPHITE REAR WING MOUNT 2.5MM - 373036

XRAY X1'19 GRAPHITE REAR WING MOUNT 2.5MM - 373036

XRAY X1'19 GRAPHITE TOP DECK 2.5MM - 376232

XRAY X1'19 GRAPHITE TOP DECK 2.5MM - 376232

XRAY X1'19 ALU SERVO MOUNT - ORANGE - 376260-O

XRAY X1'19 ALU SERVO MOUNT - ORANGE - 376260-O

XRAY X1 1/10 FORMULA BODY - WORLD CHAMPION EDITION - 379702

 

High-performance, low-profile aerodynamic body designed to perfectly fit the X1 and work under all track conditions while keeping the coveted classic F1 look and style. The front & rear of the body have been designed to provide balanced downforce for maximum stability and directed airflow onto the rear wing. The body & cockpit sides are as flat as possible to direct airflow around the body for maximum stability. The body is made from high-quality premium Lexan™ material. The integrated helmet ensures the body is legal for races where a pilot figure helmet is required.

 

XRAY GRAPHITE GEAR BOX HEIGHT ADJUSTMENT PLATE 2.2MM - 321268

CNC-machined gear box height adjustment plate made from premium-grade graphite material. Increases performance in high-traction conditions, allows super-low ride height. To keep the drive shafts linear, the gear box can be raised by 2mm using optional graphite plates. There are two different ride height adjustable plates which raise either only the gear box, or the entire rear suspension.

Must be used with #324013 Alu Front-Mid Motor (3 Gears) Plate - Lowered -2mm - 7075 T6.

XRAY SHORT 2-PAD SLIPPER CLUTCH SET - SHOCKS IN FRONT - 324000

Short 2-Pad Slipper Clutch Set - Shocks in Front

• Allows frontward shock absorber mounting position
• Super narrow
• Externally adjustable
• Quick & easy tuning
• Ultra-efficient
• Lightweight
• Increases stability
• Higher cornering speed
• Better landings

Redesigned slipper clutch set allows the rear shock absorbers to be mounted frontwards. Frontward mounting position increases stability on surfaces where the rear of the car collapses, particularly in high-speed corners. Team drivers also prefer this position on low-grip tracks.

Power from the motor is transferred to the drivetrain via an externally-adjustable central slipper clutch for quick & easy tuning. The 2-pad slipper clutch ensures super-smooth clutch operation and efficient, consistent braking. It is very easy to make ultra-fine adjustments to the slipper clutch externally.

The slipper clutch pads are made from ultra-efficient SLS material with very-high slip efficiency, thus allowing very precise slip adjustment.

The lightweight slipper plates are machined from premium Swiss 7075 T6, additionally hardened before a final black surface treatment.

The plates have a machined relief which decreases the friction surface to assist with clutch slip adjustment. With this plate design, pressure is focused on the circumference of the clutch pads for increased efficiency.

Set includes 2-pad spur gears:

• #365775 Composite Slipper Clutch Spur Gear 75T/48P
• #365778 Composite Slipper Clutch Spur Gear 78T/48P

XRAY ALU FRONT-MID MOTOR (3 G.) PLATE - LOWERED -2MM - SWISS 7075 T6 (3MM) - 324013

Black-coated, Swiss 7075 T6 aluminum front-mid motor plate lowered by 2mm. Holds the slipper clutch assembly and gear box. Allows super-low ride height, and increases performance in high-traction conditions.

XRAY ALU FRONT-MID MOTOR (3 G.) PLATE - LOWERED -4MM - SWISS 7075 T6 (3MM) - 324015

Black-coated, Swiss 7075 T6 aluminum front-mid motor plate lowered by 4mm. Holds the slipper clutch assembly and gear box. Allows super-low ride height, and increases performance in high-traction conditions. 

Must be used with #321268 Graphite Gear Box Height Adjustment Plate and #321269 Graphite Gear Box Height Adjustment Plate (or #321270 XT2 Graphite Gear Box Height Adjustment Plate).