OfficinaRC 23gr Std Battery Plate - OFC-005

A new line of 3 Battery plates is added to the already existing OfficinaRC 32g (OFC-004).

These battery plates are designed to give all the possible balancing possibilities for your models.

Usable for all categories On road and Off road thanks to the diversity of weight they allow an optimal balance for all needs.

The OfficinaRC 23gr (OFC-005) 131mmx34.5mmx0.6mm is designed to be used with a standard measurement battery. This plate can be applied using double-sided tape on the battery or directly on the chassis.

XRAY Shock Absorber Membranes - Low - 308081

Silicon-rubber compensation membranes for shock absorbers. All-new low-profile shock membranes allow for easier shock rebound adjustment. 
The new Low-profile Membranes must be used with #308091 Low-profile Shock Foam Inserts, and will fit any XRAY shocks. Set of 4.

XRAY Ball-Bearing 5x8x2.5 Flanged - Steel Sealed - Oil (2) - 950508

XRAY Ball-Bearing 5x8x2.5 Flanged - Steel Sealed - Oil (2) - 950508

XRAY Composite Rear Body Back Stop (2) - 331340

Composite body back stop set for 1/10 touring cars (electric or nitro), made from lightweight composite material, provides support for the rear of body shell to prevent tucking under the rear wheels due to a collision from the rear, thus reducing lost racing time and increasing body lifespan. Posts are quickly & easily mounted, and are trimmmable for perfect fitment. Set of two, includes mounting hardware.

Hobbywing XeRun XR10 Pro G2 160A ESC - Orange - 30112607

The XR10 Pro G2 ESC is designed for 1/10th and 1/12th RC car racing.

IT features a 32-bit microprocessor, built-in BEC with maximum current of 10A and voltage adjustable from 5 to 7.4v, battery-protection circuit, dual-switch control, adjustable maximum brake force (extended to 150%) and PWM & Brake frequencies and Turbo increase & decrease rates, and switchable motor direction (CCW/CW)

Upgraded M4 Microprocessor (32-bit) for
Professional Racing

High-performance 32-bit M4 microprocessor is implemented in the XR10PRO G2 for Super-fast and precise processing of complicated data operations, this allows the ESC to have a very rapid and precise response with extraordinary potential to optimize and extend its functions further. The XR10 PRO G2 is an exceptional piece of Hardware combined with accurate and powerful software makes this ESC into a “Precise weapon” for high end professional racing.

Internal Battery-Reverse Polarity Protection Circuit

With the Built-in Reverse Voltage Protection circuit, ESC's internal parts are all protected from Cross Connection of battery power. 
(Note: the overall power system will be protected from damage when non-polarized filter capacitors are used; the standard electrolytic (external capacitors ) supplied for this ESC have no reverse polarity protection, so the capacitors (only) ,not the ESC will be damaged  when reverse polarity installation occurs.)

Innovative Dual-Switches / Removable External Switch

Internal electronic switch & external removable switch for easy and convenient  usage. The internal switch simplifies wiring while the external switch solves the issue “it’s hard to reach the built-in switch when the car body is mounted on or  inner chassis placement of ESC”. External switch is perfect for off-road applications. (Warning! This is Hobbywing’s registered patented)

Updated Drive, and Brake PWM Frequency

More available frequency values (include "Customized PWM Frequencies") for improved tuning options of the drive and brake feel.

 

Drive PWM:1-32KHz
Brake PWM:0.5-16KHz

Tunable Turbo Increase & Decrease Rates

More fine tunable values have been implemented for Turbo Increase & Decrease Rates which allows the end user to fine tune the turbo for optimal performance when racing at different size tracks .

Switchable Motor Direction

Switchable motor direction: CCW & CW for various chassis.

Super Internal BEC

Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step:0.1V) for usage with high voltage servos.

Softening Function (Hobbywing’s Patented Technology)

Softening function implemented in this ESC allows user to fine-tune the bottom end allowing for maximum controlled power of vehicles used in Modified class racing applications.

Programming/Upgrading/Data Reading Wirelessly

With Hobbywing’s “WiFi Express” module and iPhone or an Android phone (with the Hobbywing WiFi Link App installed), users can remotely program parameters, upgrade firmware and check relevant data of the ESC without leaving the control stand.

Data-logging Function

This ESC features the data-logging function which can record the maximum ESC/motor temperature, RPM and etc. in real time and allows users to check those data via a LCD program box or WiFi module after each use. In the future, new (ESC) firmware will not only record the maximum temperatures, RPM and others but also provide complete operation (status) curve for users.

MonacoRC Ball Bearings orange kit for T4'19 (14pcs) - MC-B001

This new kit is released in orange and is available for the Xray T4 19! The perfect match with the T4 orange alu parts. This new and exclusive kit is RZ shielded, (steel and rubber), that ensure the best combo for smoothness and protection!

All the ball bearings are lubricated with oil instead of grease in order to have immediate high speed and smoothness performance!

4x High-Speed Ball-Bearing 10X15X4 RZ

8x High-Speed Ball-Bearing 5X10X4 RZ

2x High-Speed Ball-Bearing 5x9x3 RZ

Corner Speed RC O-ring Grease - CS800103

Corner Speed RC O-ring Grease - CS800103

Corner Speed RC MAXI FREE 2 CV Joint Lube (10ml) - CS800104

Corner Speed RC MAXI FREE 2 CV Joint Lube (10ml) - CS800104

Bittydesign HC-F 1/10 FWD clear body 190mm - BDFWD-190HCF

The HC-F project was born from the desire to offer to all the rc enthusiast an new top quality body shell for the growing front wheel drive divison. Tested for several months the product combine a stunning realistic aesthetic together with performance at the top of the class.

 

Designed to Win

The HC-F body shell represent a new reality for drivers all around the world who always push to obtain the best result with their models.

Thanks to the collaboration with our experienced European and Asian team drivers we have been able to follow and realize valuable suggestions that have allowed us to adopt some changes to the initial project necessary to greatly improve the driving precision and reduce the rolling of the model caused by the typical high roof of all the FWD body shells.

Italian Pure Excellence

The design recalls the forms of the "queen" par excellence of real scale front-wheel drive cars produced in Japan, the refinement phase took several months to optimize every detail, the attention to detail has been obsessive in order to propose a body that could exalting the performance of the Japanese car at its best.

HC-F is a FWD body with a breathtaking look that we offer in the Racing version with widened wheel arches in order to guarantee a better aerodynamic performance optimized both thanks to the large front spilitter and thanks to the specially designed wing that generate stability and rear wheel drive as well as make the model balanced and easy to drive.

Product Features

The body it's UNIVERSAL and fit all the 1/10 190mm cars on the market; can be mounted on the traditional 4WD touring chassis as well on the the recent all new model car developed by the factories exclusively for the front wheel class (FWD)

• Made with high quality and genuine polycarbonate Lexan®
• Included in the kit a complete set of screw, nuts and large plastic washers to fix properly the rear wing
• Produced in Light Weight version, thickness of material 0,75mm
• Sold clear with protective film outside
• Included in the package a decal sheet and windows mask

3D Cad design & engineering

In order to respect our quality standards, Bittydesign have not set any limits and we have realized the HC-F project with the use of the most advanced graphics and Cad design; this process guarantees a perfect execution of the forms and details that high-tech machinery realize with 5-axis CNC milling machines.

The product Bittydesign delivers in the hands of the enthusiast represents the best available on the market today, they exploit and make full use of the most advanced technology to guarantee a result that represents at best the Italian excellence.

WTF 30mm x 10mm High Speed Fan Blow Harder - WTF3010BH9F

Featuring the industry first 9 exhaust fins design which generates a twisting wind pattern for focused air flow, hence more air to cool the object. With the 9 exhaust fins design the support structure between the case and the core has increased 3 fold, together with thicker side wall the case is so much stronger than the standard 30 mm fan. A round lip also moulded into the intake side of the fan for further smooth out the air flow. Last but not least, these fans have been manufactured with all new electronics.

Mon-Tech Mito-RX FWD/Rally body shell - 019-007

Mon-Tech Mito-RX FWD/Rally body shell - 019-007

HUDY PURE TUNGSTEN WEIGHT 5g - 293081

HUDY PURE TUNGSTEN WEIGHT 5g - 293081

HUDY PURE TUNGSTEN WEIGHT 10g - 293082

HUDY PURE TUNGSTEN WEIGHT 10g - 293082

XRAY ALU FULLY ADJ. BATTERY HOLDER + WEIGHT FOR SHORTY BATTERIES - 306195

Fully adjustable battery aluminum holder & brass weights for short pack batteries. Allows to move the batteries front and rear but also left to right for easy and comfortable weight transfer adjustment. The holder allows to move the battery which changes the Front/Rear weight balance by 4mm. Design of the battery holder eliminates any negative chassis flex.

Each of the weights (2) is 40g heavy and allows to mount the shorty battery into the center of the chassis for perfect distribution of the weight.
 

Using the shorty battery with the low profile weights allows to lower the weight of the car which helps to make the car easier to drive, more stable in the chicanes but in the same time improves the rotation of the car. 

Recommended to use especially for modified class on carpet or small asphalt tracks.

The weights are CNC-machined from brass material and additionally black coated for astonishing look.
 

XRAY ORANGE Spur Gear 84T : 48 - 305784-O

XRAY ORANGE Spur Gear 84T : 48 - 305784-O

XRAY ORANGE Offset Spur Gear 110T : 64 - 305880-O

XRAY ORANGE Offset Spur Gear 110T : 64 - 305880-O

XRAY ORANGE Offset Spur Gear 96T : 64 - 305866-O

XRAY ORANGE Offset Spur Gear 96T : 64 - 305866-O

XRAY T4'19 GRAPHITE + BRASS FULLY ADJUSTABLE BATTERY HOLDER - 306198

Fully adjustable brass battery holder allows to move the batteries in all directions - front/rear and also left/right. The adjustable battery holder allows for easy and comfortable weight transfer adjustment. The front/rear weight balance can be adjusted in 4mm range. The brass material adds extra 7.5g weight for additional weight balance adjustment of the battery side of the car. 

The battery holders allow to mount the battery tape over the top of the battery only without the instalment of the tape under the chassis which allows increased flex of the chassis and as such helps to generate more traction. Thanks to the chassis-free instalment of the tape the ride height of the car can be slightly decreased as there is no more tape under the chassis. 

The adjustable holder and the battery backstops are CNC-machined from brass material and the battery holders are machined from premium lightweight graphite material.
 

XRAY T4'19 GRAPHITE + ALU FULLY ADJUSTABLE BATTERY HOLDER - 306196

Fully adjustable aluminum battery holder allows to move the batteries in all directions - front/rear and also left/right. The adjustable battery holder allows for easy and comfortable weight transfer adjustment. The front/rear weight balance can be adjusted in 4mm range.

The battery holders allow to mount the battery tape over the top of the battery only without the instalment of the tape under the chassis which allows increased flex of the chassis and as such helps to generate more traction. Thanks to the chassis-free instalment of the tape the ride height of the car can be slightly decreased as there is no more tape under the chassis. 

The adjustable holder and the battery backstops are CNC-machined from lightweight aluminum and the battery holders are machined from premium lightweight graphite material.
 

Dash Silicon Wire 14AWG 1m - DA-771005

Dash Silicon Wire 14AWG 1m - DA-771005

Mon-Tech Racer2 Touring Electric Car Clear Body 190mm - 019-006

Mon-Tech Racer2 Touring Electric Car Clear Body 190mm - 019-006

#PHUB Magic Grip - Pink - PH47

Presenting Magic Grip!

A new era of additive is coming to your line-up! This amazing additive will offer you unlimited traction and grip like never seen before, will suit all your tracks and will improve your lap times as well as your driving experience.

Tested by drivers like Ronald Völker, David Ronnefalk and Viljami Kutvonen proves this additive to be worth giving a try!

The additive comes in a 60mL bottle with foam for an easy apply on your tyres. It offers grip depending on the time applied to your tyres (see our Grip Level Table).

Muchmore Fleta ZX Brushless Motor Fixed Timing 13.5T - MR-FZX135WF

Hiro Seiko Power Cable 60cm Silver - 12AWG - 48390

Hiro Seiko Power Cable 60cm Silver - 12AWG - 48390

Everyone knows besides gold, Silver has the highest conductivity among all the ingredients.  However, only a few manufacturers are willing to develop power cable with silver wire.  Maybe some audio equipment related industry would develop it but there’s no other manufacturer has developed something like silver wire in RC industry.



We have targeted and improved the efficiency of conductivity.  In the first time in RC history, we released 12 AWG Power Cable with Silver Wire.

●12 AWG

●Ø0.05x1786 Strands

●Withstand Voltage 250/500V

●Temperature Range -40℃~180℃

●Length 60cm

SMJ Ultra Clear Body Repair Tape (30 x 500mm) - SMJ1032

Ultimate body repair tape debuts!
This ultra clear tape is invisible so that you can apply it to the body surface.
Due to the special film used, it is extremely durable and fits well even on curved or uneven surfaces.

Made in Japan

XRAY ECS FRONT DRIVE SHAFT 81MM WITH 2.5MM PIN - HUDY SPRING STEEL - SET - 365201

The unique XRAY ECS Drive Shaft with 2.5mm pin equalizes the speed between the drive shaft and the wheel. With a unique 2-piece joint between the axle and the wheel, the same extreme wheel turning angle is divided into two shallower angles without joint binding. This means that at the same cornering speed, the inner wheel will not bind or vibrate. Drive through the corner is more stable, more precise, and easier to drive. The ECS Drive Shafts help also with improved landing after jumps.

With the ECS drive shafts, wheel vibrations and noise are decreased to minimum, steering is increased, stability of the car is increased and cornering speed and smoothness are noticeably increased as well. A must have option part.

Corner Speed RC MAXI free CV Joint lube - CS800102

Maxi Free CV Joint Lube is a deep penetrating teflon lubricant that works flawlessly in all conditions both on and off road. Unlike other wet lubricants, Maxi Free goes on wet and setup with a supper dry, hard and extremely durable thin film that wicks away dirt, carpet hair or tyre rubber during the races. Maxi Free is the answer for racers who looking for a super clean, long lasting and low friction CV joints and universals.

Shake well before use. Apply on clean joints to maximise the performance of the lube.

-Long lasting
-Super dry lube
-Doesn’t attract dirt
-Extra smooth operation
-Feature a needle tip bottle, easier to apply on small parts

XRAY PURE TUNGSTEN CHASSIS WEIGHT 13g (2) - 306550

Machined 13g pure tungsten chassis weight. The weights are smaller than the brass weights and are easier to install with a cleaner layout. The super small weights result in lower CG comparing to standard weights. 

Produced from very rare and heavy pure tungsten material, not a typical tungsten mixture. The pure tungsten has the highest density structure and is the heaviest metal material which allows to design smallest size weights comparing to any other materials.

Quick & easy attachment to chassis. Marked with weight value for easy identification. 
 

XRAY PURE TUNGSTEN CENTER CHASSIS WEIGHT 30g - 309856

Machined 30g pure tungsten chassis weight. The weights are smaller than the brass weights and are easier to install with a cleaner layout. The super small weights result in lower CG comparing to standard weights. 

Produced from very rare and heavy pure tungsten material, not a typical tungsten mixture. The pure tungsten has the highest density structure and is the heaviest metal material which allows to design smallest size weights comparing to any other materials.

Quick & easy attachment to chassis. Marked with weight value for easy identification.
 

LRP X22 Stock Spec - 10.5T - 520200

LRP X22 Stock Spec - 10.5T - 520200

LRP X22 Stock Spec - 13.5T - 520201

LRP X22 Stock Spec - 13.5T - 520201

LRP X22 Stock Spec - 17.5T - 520202

LRP X22 Stock Spec - 17.5T - 520202

LRP X22 Stock Spec - 21.5T - 520203

LRP X22 Stock Spec - 21.5T - 520203

Hiro Seiko M3x8 Titanium Hex Socket Flat Head Screw - 69688

Hiro Seiko M3x8 Titanium Hex Socket Flat Head Screw (5)

Corner Speed RC MaxRev Bearing Oil - CS800100

Corner Speed RC MAX-REV high speed bearing oil is a low viscosity thin lubricant that designed to last. Has been carefully formulated and tested to maximise the efficiency of the lube in the toughest conditions. It contents a very special addition that help the lube working consistency in extremely high speed rotation bearings and circulating parts. 

MAX REV is the choice of all serious racers who looking for some extra bits that help boosting their performance in serious competitions. It features a 10ml needle tip bottle that make it easy to apply on any small bearings and parts.

MonkeyKingRC Charge Lead XH2S Balance Port-B - MK2976BK

2S Lipo charge lead with 4mm charger input plugs and 4-5mm battery plugs, including 2mm balance plug. 600mm. Extremely versatile, suits a wide range of chargers!

Mon-Tech M-Truck 2.0 - 019-003

The body utilises only three parts - the base, cabin and rear wing, making it both lightweight and durable and it incorporates details such as a mock-up engine and the ability to fine-tune the wing setting for low and high downforce. The shape ensures it can be mounted on all kinds of touring car chassis without having to cut the front bumper and it is made of high-quality 0.75mm polycarbonate. Included with the body set come window masks, a decal sheet and the needed assembly hardware.

XRAY LEXAN REAR WING - LOW TRACTION - 323513

XRAY LEXAN REAR WING - LOW TRACTION - 323513

XRAY LEXAN FRONT WING - DIV - 323516

Stylish, effective wider front wing works perfectly with XRAY XB2 body and increases front down force. Multiple mounting positions allow to change the position of the wing and alter the down force. Made from strong high quality Lexan material.

XRAY LEXAN REAR WING - TEC - 323517

Stylish, effective rear wing works perfectly with XRAY XB2 body. Flat design helps to get more rotation coming into the corner and increases traction coming out of corner. Made from strong high quality Lexan material.
 

XRAY GEAR DIFFERENTIAL 1/10 PAN CAR - SET - 374902

 

XRAY self-designed, revolutionary, super-smooth gear diff for 1/10 pan cars is a direct replacement for the ball-differential; it is a complete set which requires no other extra parts and no extra adjustments. Using the gear differential makes the car more stable and easier to drive, especially in high-traction conditions. The gear diff increases on-power steering which is needed on almost all types of tracks. A “must have” for every racer. The complete gear differential set includes a composite case and cover, precision-molded internal satellite gears made from special XRAY-developed composite material, all ensuring long lifespan and super-smooth efficient operation. A super-strong hollow steel shaft ensures maximum reliability and strength. The advantage of the gear diff is that it is maintenance-free. When the diff is correctly built, there is no need for maintenance for a very long time, no need for frequent oil changes, and no leakage due to a superior sealing system.

 

HUDY ALU TRAY FOR ON-ROAD DIFF & SHOCKS - 109800

Professional, ultra-compact work tray for diff & shocks rebuild. CNC-machined from one-piece aircraft aluminum. Extremely durable and wear resistant thanks to the hard black coating. The parts tray features 4 compartments for each of the shocks laser edged with label. Perfect for 1/10, 1/12 & 1/8 on-road cars. Includes easily removable aluminum shock stand. Shock stand sets are available separately to convert between vehicle types. Machined pockets feature super thin walls for weight saving. Stylish chamfered edges and laser engraved HUDY graphics makes your tray stand out on your pit table.

HUDY ALU TRAY FOR SET-UP SYSTEM - 109860

HUDY Alu Tray for Set-Up System
 

• Ultra-compact work tray for set-up system & tools

• Features various compartments for set-up system parts, shock stands, set-up wheels, balancing tools, and other accessories

• Rear part of the tray features slot for set-up system upside measurement plate

• CNC-machined from 1-piece aircraft aluminum for durability

• Machined pockets with super-thin walls for weight saving

• Stylish chamfered edges

• Super-hard coated for wear resistance protection

• Perfect for all classes & scales
 

Professional, ultra-compact work tray for set-up system and tools. CNC-machined from 1-piece aircraft aluminum. Extremely durable and wear resistant due to hard black coating.

The parts tray features various compartments for set-up system parts, shock stands, set-up wheels, balancing tools, and other accessories. Perfect for all classes and scales. Rear part of the tray features slot for set-up system upside measurement plate.

Machined pockets feature super-thin walls for light weight. Stylish chamfered edges and laser-engraved HUDY graphics makes your tray stand out on your pit table.

#109860 HUDY Alu Tray for Set-Up System

HUDY ALU TRAY FOR ACCESSORIES & PIT LED - 109880

HUDY Alu Tray for Accessories & Pit LED


•          Ultra-compact work tray for accessories, Pit LED, and mobile phone
•          Features 4 different compartments for accessories & hardware
•          Middle compartment fits perfectly to #107855 - HUDY Pit LED
•          Front adjustable bar holds your mobile phone
•          CNC-machined from 1-piece aircraft aluminum for durability
•          Machined pockets with super-thin walls for light weight
•          Stylish chamfered edges
•          Black coated
•          Perfect for all classes & scale
•          Part of the HUDY Tray System


Professional, ultra-compact work tray for accessories, Pit LED, and mobile phone. CNC-machined from 1-piece aircraft aluminum. Extremely durable and wear resistant. Black coated.

The parts tray features 4 different compartments for accessories & hardware. Middle compartment fits perfectly to #107855 - HUDY Pit LED. Front adjustable bar holds your mobile phone.

Machined pockets feature super-thin walls for light weight. Stylish chamfered edges and laser-engraved HUDY graphics makes your tray stand out on your pit table.

HUDY PROFESSIONAL BULKHEAD ALIGNMENT TOOL 19MM - 183000

#183000 HUDY Professional Bulkhead Alignment Tool 19mm

• Perfect bulkhead alignment
• For 19mm bulkhead spacing
• Comfortable & fast
• Lightweight 
HUDY Bulkhead Alignment Tool for touring car bulkheads with spacing of 19mm allows for easy, comfortable and fast alignment of bulkheads. 

The alignment tool is placed between the left and right bulkheads with the included steel shafts. With the block and pins in place the driver can loosen and retighten both the lower bulkhead mounting screws and also the upper clamps and shock towers for perfect alignment of all parts. After all the parts are straightened up, the pins and block will be removed, the diff or spool installed and the bulkhead upper clamps installed. 

CNC-machined from lightweight aircraft aluminum and laser edged for autentic look this is a must have tool for all touring car drivers. The alignment tool works perfectly for all XRAY T4 platforms and other touring cars with 19mm spacing between bulkheads.

XRAY GRAPHITE GEAR BOX HEIGHT ADJUSTMENT PLATE - 321269

CNC-machined gear box height adjustment plate made from premium-grade graphite material. Allows super-low ride height in high-traction conditions for improved performance. To keep the drive shafts linear, these optional graphite plates raise the gear box by 2mm. There are two different ride height adjustable plates which raise either only the gear box, or the entire rear suspension.

Must be used with #324013 Alu Front-Mid Motor (3 Gears) Plate - Lowered -2mm - 7075 T6.
 

Hobbywing XERUN V10 G3 Rotor 12.5T - 30820401

HOBBYWING  is proud to present the newest rotor(5-12.3/12.5-U-T) for the V10 G3 motor series.

The characteristic of the titanium bonded rotor provides a milder, smoother pickup acceleration without losing its top speed. The rotor will aid drivers especially on lower grip surfaces and allow drivers to accelerate quicker out of tighter corners. The rotor has been extensively tested and race proven by Top Drivers on carpet and  low grip asphalt tracks around the world. Highly recommended for all HOBBYWING XR10 Pro users on their Modified motors.

Hobbywing XERUN V10 G3 Rotor 12.3T - 30820402

HOBBYWING  is proud to present the newest rotor(5-12.3/12.5-U-T) for the V10 G3 motor series.

The characteristic of the titanium bonded rotor provides a milder, smoother pickup acceleration without losing its top speed. The rotor will aid drivers especially on lower grip surfaces and allow drivers to accelerate quicker out of tighter corners. The rotor has been extensively tested and race proven by Top Drivers on carpet and  low grip asphalt tracks around the world. Highly recommended for all HOBBYWING XR10 Pro users on their Modified motors.

BittyDesign JP8 1/10 TC 190mm body (Light) - BDTC-190JP8

When thinking about the best think about the JP8.

The ALL NEW ultra downforce body shell has been developed with the collaboration of our wordwide team drivers, who participated to the several stages of the project. The JP8 includes all of our experience gained in over 10 years of presence on the racetrack, and the final version of the body requested many changes before reach the perfect shape. To raise the bar we not accepted any compromise.

Tested for several months both indoor and even outdoor on different types of carpet and tarmac, the JP8 body shell represent a new reality for drivers all around the world who race at top levels and always want to obtain the best result with their models.

 

No Compromise

The JP8 project is born with one main target: create an all new ultra downforce body shell that can be the fastest, always. No matter what final shape and lines the body will have, how it will look, the focus during the designing stage has been pure performance.

LIGHTNESS and STRENGTH! Thanks to an excellent production process, which guarantees a high homogeneity of the material in any area of the body, we have reached a good compromise between weight and durability of the product. Several track tests have revealed excellent impact resistance, giving the JP8's extremely longevity.


 

The Art of Performance at his best

To achieve the best result possible in term of overall product we have made the most of all our know-how, our experience on the track allowed to us to develop, to design, to engineer and to test for several months a body shell that represent the new future for the 1/10 TC competitions.

The ultra downforce design generate impressive steering as well an excellent rear stability; very easy to push the car at limit, the driving feeling is great both on indoor and outdoors layouts.

---

Product Features

The body respect all the international specs necessary for the approval by the federations, its EFRA, IFMAR and BRCA homologated.

• Made with high quality and genuine polycarbonate Lexan®
• Included in the kit a complete set of screw, nuts and large plastic washers to fix properly the rear wing
• Produced in Light Weight version, thickness of material 0,75mm
• Sold clear with protective film outside
• Included in the package a few decal sheets pre-cut and windows mask

---

Track Guide for the use of the JP8 body

The following values offer an overview of the ideal conditions of use of the body according to the grip of the surface and its general handling.

The numbers below are meant as a progressive scale where 10 is a hypothetical maximum value.

   
Surface grip 
7 
Enter Steering
10
Rear stability
10
Ease of use
10

 

XRAY ORANGE Offset Spur Gear 100T : 64 - 305870-O

XRAY ORANGE Offset Spur Gear 100T : 64 - 305870-O