3.5mm diameter banana connector used for motor connection. Set of 3 female side.

Racing Performer 70mm Brushless Sensor Cable ver.2

RADTEC 110MM FLAT BONDED FLEX SENSOR WIRES 

Radtec 30mm & 40mm Aluminum Motor Cooling Fan Mount V2, Black

Radtec Flex Sensor Wire Flat Bonded 90mm

The Raytronic C30 + 300W was designed to offer an intelligent pocket charger with high performance and very simple operation. RAYTRONIC C30 + allows charging and discharging common types of cells (NiCd, NiMH, LiPo, LiHV Li-ion, LiFe, Pb), in addition it is equipped with a built-in six-channel balancer, which ensures safe and comfortable charging of lithium batteries. Measurement of voltage and internal resistance of individual cells (for lithium batteries) is a matter of course.

Features:

• Input supply voltage 10 - 26 V DC (socket XT60)
• For charging and discharging 1 - 16 NiCd / NiMH cells, 1 - 6 Li-ion / LiPo / LiHV / LiFe cells or 2- 20 V lead-acid batteries
• Adjustable charging current (0.1 A - 12.0 A)
• Adjustable discharge current (0.1 A - 3.0 A)
• Max. power for charging 300 W, for discharging 5 W
• Termination of charging using delta-peak automation for NiCd and NiMH batteries
• Lithium and Pb batteries are charged using the "constant current / constant voltage" method
• Adjustable delta-peak detection sensitivity for NiCd and NiMH batteries
• Adjustable end voltage for charging and discharging for lithium batteries
• Repeated cyclic operation of charging / discharging or discharging / charging for NiCd and NiMH batteries, up to 5 cycles
• Four charging modes for lithium batteries - normal charging, fast charging, balancing charging and storage charging / discharging
• Stop charging when the set time or the supplied charge is exceeded.
• Memory for 5 charging / discharging programs.
• Measurement of the total voltage of the set and individual cells (for lithium batteries)
• Measurement of the total internal resistance of the set and individual cells (for lithium batteries)
• The XT60 power output socket and the JST-XH 2-6S universal balancer socket allow you to connect the rechargeable battery directly without the need for a charging cable and balancer adapter (if the kit is equipped with an XT60 power connector and a JST-XH service connector)
• Two-line backlit LCD display with simple and clear menu and display of parameters during charging / discharging
• A number of warning text messages contribute to safe operation - incorrect input voltage, incorrect connection, unsuitable battery or its condition, incorrect polarity at the output
• Reverse polarity and short circuit protection at the output / li>
• Compact plastic case, small dimensions
• Built-in fan for forced cooling

Specifications:

Powerful stabilised switched-mode power supply Raytronic P20 with adjustable output voltage and current limit is perfect for powering modeller's chargers with power up to 300W and other electronic devices. It is suitable for testing electronic devices that have to be powered by 6–15V DC.

The power supply is equipped with protection circuits that protect it from short-circuit on input or from overloading. There is an active cooling system, which stabilises operating conditions and protects from overheating.

Output voltage and current limit are adjusted via knobs on the front panel - values of output voltage or current are shown on 3-digit LED display (choose between current and voltage via switch).

Thanks to an adjustable output voltage and current limit you can use the power source as a charger for batteries that need constant voltage/constant current charging mode (such as acid-lead or Li-Fe batteries, other than A123® with different chemicals and charging behaviour. Common modeller's chargers specialized for A123® cells can end the charging too soon (or completely ignore the cells) etc.
 

Specifications:

Includes:

• Raytronic P20 power supply
• Power cable
• User manual

RC MAKER Digital Caster Gauge Set for Schumacher Mi9

RC Maker productomschrijving:

Maak kennis met onze digitale zwenkwielmeter voor de Schumacher Mi9!

De digitale zwenkwielmeter toont de werkelijke zwenkwielhoek direct op de naaf.

Deze meter bevindt zich aan de bovenkant van de naaf, op dezelfde plaats als het zwenkwielgereedschap. Hij is stevig bevestigd op een koolstof plaat die een vierkante uitsparing heeft met een gleuf zodat alleen de schroef losgedraaid hoeft te worden, net als bij ons conventionele zwenkwielgereedschap. Eenmaal op zijn plaats klikt hij perfect vast.

Het zwenkwiel kan vervolgens worden afgesteld in stappen van 0,1 graad om ervoor te zorgen dat het op alle 4 hoeken van het voertuig precies hetzelfde is. Hierdoor kun je ook zeer fijne afstellingen maken van een halve graad, wat regelmatig onnauwkeurig blijkt te zijn met conventionele afstelstations.

De digitale zwenkwielmeter kan worden gebruikt op alle standaard uitlijnstations, zelfs als deze geen zwenkwielafstelling via zwenkwielmarkeringen ondersteunen. Het is een volledig afzonderlijk meetapparaat dat niet afhankelijk is van een onderdeel van het uitlijnstation zelf om het wiel te meten. Dit zorgt ervoor dat bij het kopiëren van afstelbladen en afstellingen van andere rijders, de caster meting echt is en niet van een specifiek merk afstelstation.

De nauwkeurigheid van deze meter is ongelooflijk. We hebben meerdere hoeken gebruikt om ervoor te zorgen dat de nauwkeurigheid altijd precies en consistent is. Tests hebben aangetoond dat alle meters binnen 0,01 graden tolerantie liggen over een casterbereik van 6 graden van de Schumacher, zodat je je casterinstellingen keer op keer kunt reproduceren. Elke digitale zwenkwielmeter wordt getest voor de verkoop en een perfecte kalibratie is elke keer gegarandeerd.

Je kunt deze meter op elke hoekbank/zetplank gebruiken omdat de 'nul' functie je in staat stelt je aan te passen aan elk hoekoppervlak waarop je werkt. Stel het apparaat aan beide zijden van je werkbank op nul voor gebruik en je hebt de hele dag nauwkeurige metingen!

Het apparaat wordt geleverd met een beschermhoesje zodat het gloednieuw blijft, en een AAA-batterij voor de werking, die eenvoudig vervangen kan worden als hij leeg is.

Traditionally chemicals such as brake cleaner and nasty petroleum based solutions have been used to clean and additive tires. This is harmful to the environment and most importantly to the human body. Throughout our 15+ years of racing, we have seen more health issues from the use of these dangerous chemicals than we care to admit. These health issues can be caused by inhalation of the chemicals, or physical skin exposure which is then absorbed into the blood stream.

This was our motivation to develop a range of tire cleaners and additives that are safe to use, not harming your body, or the environment. The first of which... Dominate!

We are quite aware that most racers won't sacrifice lap-times for the sake of their health, and thats why we have conducted extensive testing to ensure that Dominate out performs every other cleaner on the market! Not only is it safe to use, it's also fast!

Our Dominate Tire Cleaner has been developed by a dedicated local Australian Racer over the past 12+ months. Developed with the aid of several top drivers and certified chemists, we were able to discover an environmentally friendly non-toxic way of softening and conditioning rubber without drying it out, like you've never seen before! Opening up the pores of the rubber is crucial to the absorption of the tire additive and thus its effectiveness of creating more traction and reducing "drop off" over a run.

Dominate is supplied in a pump spray bottle for easy application on both onroad and offroad rubber tires. Simply spray onto a rag or towel and firmly wipe the tire with the cleaner. Allow to sit for at least 1 minute until sticky, before applying the tire additive. Dominate's cleaning capability can be even further increased when tires are cleaned at higher RPM on a tire sander.

Dominate can be used with both new and old tires, and provides a brilliant base for maximum absorption end effectiveness of the tire additive.

If you run out - just grab a Dominate Refill pouch here! Save the environment and your pocket.

Try some today - Help your body, the environment and your lap-times!

Features:

• Environmentally Friendly - Biodegradable and non-toxic
• Much safer for daily use on the body
• Fresh eucalyptus "green" odour
• Softens and restores rubber tires, without drying them out
• Extremely effective on Rubber tires in Onroad & Drag, as well as Offroad
• Improves absorption of additives and compounds added to the tire after cleaning
• Comes in a blacked out 100mL spray bottle with cap
• MSDS Available

These 3D Printed Mounts allow the Arrowmax Tire Warmers to be mounted inside our brand new GeoCarbon Car Stand for 1/10th & 1/12th Onroad! 

Warming your tires is much easier when they're part of a car stand, simply turn the warmers on, sit your car on top and place the cups on the tires! If you still want to use the car stand for working on your car, you can simply unplug the warmer cups and power cable, and you have a normal stand with no wires. 

You can also still use the original Arrowmax Warmer Case even when the warmer is installed in the car stand, just remove the foam and all the components will fit directly into the case with ease. 

Features:

• "Builds-in" the warmers into your GeoCarbon Car Stand
• Supports the car while warming, all in one place taking up less room
• Fits seamlessly back into the Arrowmax Warmer Case (without foam)
• Super easy installation in minutes and can be removed at any time
• High Quality and Durable 3D Printed Material that simple slides over the warmers without damaging them. 
• Includes all mounting hardware to attach to car stand 

The car stand features anti-slip rubber feet, as well as anti-slip thin rubber on the top, ensuring your car stays put and there's no damage to your chassis or the car stand! 

The stand is finished off in our GeoCarbon styling, along with chamfered edges to keep things smooth.

The added bonus of this design, is that you can mount your Arrowmax tire warmers inside! Giving them a platform for you to sit your car while you warm. You must purchase the additional Arrowmax Warmer Mounts #RCM-CS2-ONR-AM

Features:

• Stylish GeoCarbon Design
• 5mm Thick Durable Carbon Construction 
• 7075 Black Anodized Posts
• Anti Slip Rubber finishings top and bottom
• Ability to mount Arrowmax Tire Warmers Inside
• CNC Machined with RC MAKER Logo 

Includes:

• 1x GeoCarbon Car Stand 

Additional Options:

• Arrowmax Tire Warmer Mounts (not included) #RCM-CS2-ONR-AM

RC Maker GeoCarbon HD Weighted Tweak Wheel Set Pro for 1/10th Onroad

Featuring a more stylish updated design that also increases the usability, durability and accuracy of the tweak wheels! 

• Longer thumb nuts for easier attachment  
• New chamfered nuts tighten down to hex without shims
• Smaller range of motion once wheel lifts, for faster resetting
• One-piece weight/bulkhead design for increased rigidity and durability
• Premium dual colour lock in base for easy transport
• Our signature GeoCarbon styling 
• Stylish chamfered, black coated and laser engraved brass

No more getting down on your knees at your pit seeing which wheel picks up first, with our weighted tweak wheels, you can easily identify which wheel is lifting earlier! With offset weights, the tweak wheels will spin as soon as the earlier lifting corner comes off the ground, making it extremely easy to accurately identify what tweak adjustment needs to be made to de-tweak the car.

The set of Weighted Tweak wheels features ABEC 7 Bearings, Black 7075 Knurled thumb nuts and Black Coated and laser engraved bulkhead/weight!

The nuts are permanently installed in the bearings, which are permanently installed in the brass bulkhead. As a complete assembly, you will never lose anything, as each wheel, nut and bearing assembly is fixed together. 

The set is topped off by a dual colour 3D Pro Tweak Wheel Stand, which keeps them together on your pit bench and in your pit bag!

These work great on both EP and GP 1/10th Touring Cars with a standard 4mm axle.

Features:

• Lightweight and easy to transport, install, and remove
• Ensures incredibly accuracy
• No need to move your body position to identify which wheel is lifting first, can be observed from normal pit sitting position
• No need to swap wheels front to rear, both pairs are the same and can be used at either end.
• Perfectly fitting stand to keep the wheels together and organised on your pit bench
• Blacked out bulkhead with Laser engraved RCM Logo, Black 7075 Alu Knurled Nuts, ABEC 7 high tolerance bearings with a 3K Carbon Fiber attachment
• All components are CNC Machined and assembled to very high tolerance

Directions for successfully de-tweaking your chassis:

1. It's very important to ensure your chassis is flat, and droop is set prior to doing this process!
2. Rotate the wheels on the opposite end of the car you're checking, so the flat base is in contact with your setup board.
3. Ensure the weighted tweak wheels on the end you're working on are parallel to the ground, with the logo horizontal.
4. Press down on both ends of the car to settle the suspension and then lift the "spinning" end up slowly until one of the wheels starts to rotate, note which wheel it was.
5. The wheel that came off early is the side that the collar needs to be unscrewed towards the top of the shock body on the other end of the car. Adjust half a turn, and do the opposite direction to the other side by half a turn also. E.g. If the front left lifts early, unscrew the rear left collar half a turn, and tighten the rear right collar half a turn.
6. Repeat the process until you have both wheels spinning at very close to the same time. 
7. To do the other end, simply rotate the car 180 degrees, rotate the wheels that were fixed back to spinning, and the previously spinning back to fixed, and repeat above steps!

RC MAKER Pro Carbon Ultra-Lite Anti Tuck 1:10 Touring Car

RC MAKER Pro Hood Stiffener for Mugen MTC2 + Xray X4

RC Maker Productbeschrijving

Maak kennis met onze gloednieuwe 3D Pro Carbon Bonnet Stiffener die compatibel is met de originele kitbeugels voor de Mugen MTC2, MTC2R en XRAY X4 modellen!

Onze motorkapversteviger maakt contact met de carrosserie. Het verminderen van de buiging van de carrosserie verbetert de downforce door de motorkap en de voorruit. Dit onderdeel wordt rechtstreeks op de bumper geschroefd en kan worden gebruikt met zowel schuimrubberen als 3D-geprinte bumpers. De schroef aan de bovenkant van de assemblage kan worden aangepast om de hoogte perfect af te stemmen op de carrosserie. Ze wegen slechts 1,5 g, waardoor ze de lichtste motorkapversteviger op de markt zijn! 

Gemaakt van 1,5 mm dik koolstofstaaf en de nieuwste 3D-printtechnologie van hoge kwaliteit en hoge resolutie voor maximale stijfheid en duurzaamheid! 

We raden aan een kleine hoeveelheid schuim te gebruiken waar de body de beugel raakt. Dit voorkomt dat de schroef aan de binnenkant van de body wegglijdt, waardoor de verstijving nog effectiever wordt. Het voorkomt ook dat de verf van de carrosserie afbladdert!

Gebruikt door wereld-, Europees en ETS-kampioen Ronald Völker!

Kenmerken:

• Direct te monteren op elke bumpersteun op de MTC2 en X4 platforms
• Versterkt de motorkap, voorkomt dat de wielkasten breken en verhoogt de downforce
• Stabiliseert de carrosserie bij hoge snelheid om vervorming te voorkomen 
• Ultralicht gewicht van slechts 1,5 g incl. stalen schroef
• Verstelbaar met een M3-schroef (meegeleverd), met de optie om een langere schroef te gebruiken voor hoger gemonteerde carrosserieën.
• Vervaardigd en geassembleerd in Australië met hoogwaardig 3D-geprint filament. 

Inclusief

Bonnet versteviger

1x M3x5 schroef voor aanpassing (kan worden vervangen voor andere hoogte-instellingen)

RC-Parts RC14006-BLK Tool Stand Aluminium zwart voor 20 gereedschappen

RC11005 BODY REAMER

The world’s smallest transponder now in a pitch-black design helping you race in style. This device is compatible with all MYLAPS RC4 timing systems (with all firmware versions).

Detail

Our RC transponders help you to track lap times and give better insights in your performance.
You install the transponder in your RC car. If you race with multiple RC cars it’s convenient to install a transponder in every car. A transponder has a seven-digit number.

Features:

• The RC4 Pro transponder is 25% smaller than the RC4
• A shorter 8cm cable ensures a perfect fit every time
• It weighs only 3 grams
• All your results in your personal profile.
• RC4 transponders can be used for both indoor and outdoor racing and will perform on just about any surface.
• Compatible with MYLAPS RC4 timing systems.

Specifications:

Light oil for bearings and transmissions etc. Easy to use pen type needle applicator.